Q1. Which is the correct statement to describe the Shift Interlock Mechanism?
Locks the transmission in 1st gear
Selector lever can be moved out of P- Position when the Key is inserted and not in Lock position
Locks the transmission in L range
Locks the transmission in neutral for towing.
Q2. What is the correct temperature required for checking A/T oil level?
50~60 °C
110~120 °C
90~100 °C
70~80 °C
Q3. The Hivec Automatic transmission also has a Main oil filter which should be replaced when?
After 60,000 km
After 90,000 km
After 120,000 km
Only when transmission is overhauled
Q4. Adjustment of the inhibitor switch, select the correct position.
Set the selector lever to the `N´ position
Set the selector lever to the `P´ position
Set the selector lever to the `D´ position
Set the selector lever to the `L or 1st ´ position
Q5. Which is the correct guideline when towing a vehicle with automatic transmission?
Maximum towing distance is 50 km and maximum towing speed is 50 km/h
Maximum towing distance is 40 km and maximum towing speed is 40 km/h
Maximum towing distance is 30 km and maximum towing speed is 30 km/h
Maximum towing distance is 20 km and maximum towing speed is 20 km/h
Q6. For transmissions fitted with a `Sub´ oil filter, how can you identify the difference between A/T and Engine oil filter?
Color of A/T filter is Blue
Color of A/T filter is Black
Is stamped on top with `A/T Only´
They have different threads and are not interchangeable
Q7. Why is it necessary to replace the brake fluid every 1~2 years ?
Brake fluid becomes dirty after this time
Brake viscosity becomes too low
As a mineral oil brake fluid has a limited life time
Brake fluid is hydroscopic and absorbs moisture through the brake hoses
Q8. A Braking system for Diesel engine cars is fitted with a senor ? switch as shown in the figure. What is its purpose?
To detect hydraulic fluid leakage
To measure the level of vacuum in the brake booster
To measure the level of pressure in the brake booster
To switch on the brake lights when brakes are applied
Q9. When three resistors are connected in parallel, which of the following equations are resistance value(R)?
R = 1/R1 + 1/R2 + 1/R3
R = R1 x R2v X R3
R = R1 + R2 + R3
1/R = 1/R1 + 1/R2 + 1/R3
Q10. In the circuit below, which of the following value of current I is correct?
1 ampere
2 amperes
3 amperes
4 amperes
Q11. In the circuit below, which of the following value of current I is correct?
2 amperes
3 amperes
4 amperes
5 amperes
Q12. In the circuit below, which of the following value is correct as the voltage drop caused by the 0.4 ohms resistor?
1 volt
2 volts
3 volts
4 volts
Q13. Which diesel system has a fuel heating circuit integral of the fuel filter?
Bosch
Delphi
Siemens
Lucas
Q14. Which CRDi engine is not fitted with glow plugs?
A-Engine (D4BH/BB)
D-Engine (D4EA)
U-Engine (D4FA)
J-Engine (J-3)
Q15. What is the correct compression ratio for a diesel engine?
22:1
10:1
8:0
45:1
Q16. In gasoline engines, during initial starting, what is the main component used for calculation of the basic fuel injection amount? (before correction )
Throttle position sensor
Coolant temperature sensor
Intake air temperature sensor
Mass air flow sensor
Q17. In gasoline engine ignition system, what is the component used for calculating the initial ignition timing? (before correction)
Camshaft position sensor
Crankshaft position sensor
Coolant temperature
Mass air flow sensor
Q18. To improve drivability during cold engine operations the ignition timing is?
Advanced
Retarded
Not changed
Only traded when knock occurs due to richer mixture
Q19. From the items mentioned below which one is correct as an input to engine control module (ECM)?
Throttle position sensor
Injector
Main relay
Fuel pump relay
Q20. In gasoline engine ignition systems, a knock sensor is applied. What happens when a knock is detected?
Ignition timing is advanced
Ignition spark is prohibited for the knocking cylinder
Ignition timing is retarded
Injector is turned OFF in the knocking cylinder
Q21. What is the correct name of the marked area in the below figure?
Piston upper ring zone
Piston roof
Piston head
Piston top land
Q22. Which one is used when calculating an engines compression ratio?
Power and Torque
Bore and Stroke
Compression pressure and volume
Cylinder displacement and pistons
Q23. Technician A says the clutch system on the following picture is a pull type, so you must take care about the special procedure required to remove the transmission. Technician B says the clutch system on the following picture is a push type, so it is not required any special procedure for removal of transmission. Who is correct?
A
B
Both of them
None
Q24. Following picture explains the principle of?
Self adjusting clutch
Conventional flywheel
Dual mass flywheel
Concentric slave cylinder
Q25. Following picture shows the inner structure of?
Helical gear type self locking differential
Fully locking type differential
Multiple disc type self locking differential
Conventional differential
Q26. A 5 speed transmission is shown in the figure. The yellow line is showing the power flow when which gear is engaged?
1st Gear
2nd Gear
4th Gear
Reverse Gear
Q27. Choose the correct name on the blank.
>
Buckle pretensioner
Belt pretensioner
Side airbag
Curtain airbag
Q28. Following picture shows the principle of
Vehicle inertia sensing retractor (VISR)
Webbing inertia sensing retractor (WISR)
Buckle pre-tensioner
Seat track position sensor
Q29. Following is the general operating sequence for airbag deployment. Choose the best statement in the blank.
Crash sensing
Vent gas (bag deflation)
Airbag system completed
Produce Nitrogen Gas to Inflate the Airbag
Q30. Following picture shows the purpose of
Active headrest
Power seat
Safety power window
Back warning system
Q31. Following figure shows the hydraulic control valve for power steering system. Choose the correct part name of the indicated one.
valve spool
sleeve
torsion bar
pinion
Q32. A technician is removing the fuel pump fuse for air bleeding of power steering system. What is the purpose ?
To save the fuel and battery power while air bleeding
To avoid excessive engine load while air bleeding
There is a risk that the air cause foaming of the fluid if it is done while engine running
To reduce the working time for air bleeding
Q33. Following picture is for general construction of power steering system. Choose the correct answer in the blank.
Pressure hose
Suction hose
Return hose
Oil reservoir
Q34. Following picture is an internal structure of hydraulic control valve for power steering system. When the mentioned 'failsafe connection' is used ?
When the fluid is leaking
When the engine is stalling
When the hydraulic control valve is stuck
When the torsion bar is broken
Q35. .In the below figure what is being described by the red line ?
Side thrust indicator
Toe out on turns for raer axle
Thrust line
Positive camber of rear wheels
Q36. Read the measured result on the following micrometer.
38.45mm
38.95mm
38.40mm
38.50mm
Q37. Read the measured result on the following dial gauge.
-0.1mm
0.1mm
-0.01mm
0.01mm
Q38. Following measurement is to find out the
Temperature of shaft
Bearing clearance
Dimension of journal
Bearing type
Q39. .Choose the correct name of the bearing.
(A) Radial ball bearing, (B) Needle bearing
(A) Needle bearing, (B) Radial plane bearing
(A) Tapered roller bearing, (B) Needle bearing
(A) Cylindrical roller bearing, (B) Radial plane bearing
Q40. Choose the answer on the blank.
Heat treatment index
Material index
Thickness
Pitch
