Q1. The parts in the following picture is for ?







MAP
ETS
EGR
VIS

Q2. Following picture shows?








Injector
Fuel pump
Vacuum actuator
Oil control valve for CVVT

Q3. Choose the best answer on the following blank. "Do not supply battery voltage to a low ( ) type injector directly, as this will damage the injector"









Resistor
Temperature
Leak
Density

Q4. Below picture shows ignition power TR circuit. The red line marked with '?' is will be connected to ?







ECM
IG2
Main relay
Ground

Q5. Following picture explains?





IAT
Speed density
Karman vortex
None of the above

Q6. The indicated part in the following picture will be?






MAF sensor
MAP sensor
Knock sensor
PCV

Q7. Which of the following is proper description for the waveform below ?








EGR solenoid valve
Injector
CKP
PCV solenoid valve

Q8. Following picture shows the variation of interface for


















Engine coolant temperature
Vehicle speed
Engine oil pressure
Input shaft speed

Q9. Choose the correct description for the following picture



The valve assembly consists of two electrical coils only.
AC current is used for control by ECM.
Power is supplied from main relay.
Self learning function is provided to cope with wear.

Q10. This terminal is used to control the alternator output via the ECM. By this signal the output increase of the alternator can be delayed to avoid a sudden decrease in idle speed. What is this?
L
B
TR
G

Q11. Following picture explains two types of ( ).






Wheel speed sensor
Vehicle speed sensor
Input shaft speed sensor
CKP / CMP

Q12. Some of the engine ECM has a certain sensor inside ECM as shown in the following picture. Choose the proper one.








MAP sensor
MAF sensor
Barometric pressure sensor
Engine coolant temperature sensor

Q13. Following diagram is describing TPS operation. Choose the best answer in two blanks.







Close, Open
Open, Close
Close, Close
Open, Open

Q14. Choose the proper answer in the blank.








IAT
Injector
APS
Power TR

Q15. Choose the correct statement regarding the following picture.
















It is called as variable intake system (VIS).
It opens fully for the limp home in case of faulty system.
The mechanical cable also equipped for the failsafe.
The idle speed actuator is not necessary anymore.

Q16. The throttle position sensor can be checked with ________.
A digital voltmeter
An ohmmeter
Both 1) and 2)
Neither 2) nor 2)

Q17. Which of the followings is correct for the SMARTRA 3 immobilizer system?
There is nothing to do after replacing SMARTRA unit
Possible to use ID key to register additional keys
SMARTRA unit cannot be reused
SMARTRA unit has a vehicle information

Q18. Which of the followings is applied item for epsilon engine?
DLI type ignition coil
ETC(Electrical Throttle control)
EGR valve
SCV(Swirl control valve)

Q19. Which of the followings is correct for the features of A-2.5 EURO IV engine?
2 timing chains are applied in A-2.5 engine for connecting camshaft and crankshaft
The maximum fuel pressure reaches 1,350bar
Electrical type low pressure pump is adopted in fuel tank.
IQA (Injection Quantity Adaptation) injectors are applied

Q20. Which of the followings is correct for Gamma engine?
Hydraulic lash adjusting mechanism is applied
It has vane type CVVT system
Maintenance free timing belt is applied
Two serpentine type driving belts are applied

Q21. Which of the followings is correct for the added items for EURO IV U-1.6 engine comparing EURO III?
HLA (Hydraulic Lash Adjuster)
MAF sensor
EGR valve
SCV(Swirl control valve)

Q22. Followings are explanation of gamma engine (in LD F/L) diagnosis, which of following is correct explanation?
2 driving belt is used. So, do not interchange each other.
For diagnosing gamma EMS by hi-scan pro, CAN adaptor is needed
Timing chain is replaced every 100,000 km
Long reach type spark plug is used, so, do not interchange with conventional type spark plug

Q23. Following sensor in the picture is for?






CPF
EGR
VGT
Rail pressure control

Q24. When the indicated part in following picture is failed,



Possible to replace the part only.
Related sensor also must ne replaced.
Rail assembly must be replaced.
Nothing to do.

Q25. Choose the correct answer in the blank.















Serial number of injector.
Applied engine code.
Calibration mark for injector.
Requested fuel.

Q26. Choose the correct name of indicated part in following picture.


Rail pressure control valve
Rail pressure sensor
Pressure limiter valve
MPROP

Q27. Following two sensors in the picture are for?



EGR control
CPF
VIS
CVVT

Q28. After replacing the sensor in following picture,




Exhaust gas temperature sensor 1, 2 also must be replaced together.
Must burn the soot inside the CPF
Must replace the ECM also.
Must reset by scanner.

Q29. Choose the correct answer in the blanks.






A: Fuel supply, B: Fuel return, C: High pressure
A: Fuel supply, B: High pressure, C: Fuel return
A: Fuel return, B: Fuel supply, C: High pressure
A: Fuel return, B: High pressure, C: Fuel supply

Q30. Choose the proper purpose of part in following picture.
A: Anti-judder function while engine off.
B: Intake air control for EGR.
C: Exhaust gas temperature control for CPF regeneration.
D: Pilot injection control.








A, D
A, B, C
B, C, D
All of them

Q31. Choose the correct statement about the oxygen sensor in CRDi system as shown in following picture.











It is not possible to link up a voltmeter or an oscilloscope to measure the sensor output directly
The main task is to measure the air/fuel ratio in the intake air.
It is only for EGR control.
The heater should not be incorporated.

Q32. Select the correct symbol to fill in the blank(with question mark) in the figure below.



















A
B
C
D

Q33. When replacing the ECM in SMARTRA system,
Antenna coil also must be replaced together.
You don't have to know original PIN for key teaching.
You need original PIN for key teaching.
Key teaching is not necessary.

Q34. Choose the correct statement for the following picture.









Can be used as an ID key for key registration.
Cannot open the trunk.
Can open the g/box.
Must not be used for daily use.

Q35. Choose the correct name of the part in the following picture.






CSD (Cold Starting Device)
SMARTRA unit
ICM
Fuel cut valve controller (DDS)

Q36. According to the following picture, we can assume that









It is a Shinchang immobilizer system.
The ECM must be neutralized.
PIN was lost.
The ECM is new one.

Q37. The act in the following picture may






Cause problems during registration.
Cause problems during vehicle starting.
Both 1 & 2
None of the above

Q38. When you lost the key in SMARTRA immobilizer system,
Replace the ECM and register new blank key.
Replace the ICM and make neutralization.
Try to do the limp home function with ID key.
Register new blank key with PIN.

Q39. Following is the sample for the limp home function in immobilizer system. Read out the password.














2345
3345
3245
Cannot identify

Q40. When you replace the ECM and key cylinder,
Must know original PIN for new key teaching.
Arbitrary 6 digits code is available for new key teaching.
Antenna coil also must be replaced.
Must neutralize the ECM.