Q1. Which of the followings is correct for the part in the following picture?
It has the driving pattern data for each driver.
The memorized data in this part can be erased.
Whenever replace the TCM, this part also must be replaced.
It has the hydraulic pressure data for the valve body.
Q2. Following is the condition for the TCM learning in A5SR1 A/T model. Choose the correct answer in the blanks.
20, 4th
80, 4th
20, 3rd
80, 3rd
Q3. The reverse lamp relay and starter relay are controlled by ( ) in the vehicle equipped with A5SR1 model A/T.
Engine ECM
A/T TCM
Body control module
MDPS control module
Q4. Which of the followings is correct for the statements of A4CFx?
It has total of 7 solenoid valves
VFS has been applied for the variable line pressure
Kick down band must be adjusted for maintenance
The outside A/T oil filter on the transaxle case must be replaced periodically
Q5. Which of the followings is correct for the part name indicated in the following picture for new alpha A/T? 
ATF temperature sensor
Pressure switch
VFS
Sub ROM Unit in valve body
Q6. The work in following picture must be done whenever 
Engine ECM is replaced
TCM is replaced
A/T assembly is replaced
Torque converter is replaced
Q7. Choose the correct answer in the blank. (based on the A4CFx A/T model) 
ON
OFF
Q8. Choose the correct statement regarding the part in the following figure. 
It is located in the rear differential.
Electronic magnetic clutch is incorporated.
It connects the transaxle and propeller shaft.
Front wheel speed sensor is incorporated.
Q9. Choose the wrong statement about the advantages of 4WD vehicle compared to a 2WD vehicle.
4WD is helpful to support directional stability
4WD is helpful to go faster
4WD is not helpful to stop the vehicle
4WD consumes more fuel
Q10. Which of the following statements is correct?
TOD shift motor is not interchangeable with an EST shift motor.
TOD shift motor looks different as an EST shift motor.
TOD has one speed sensor only.
EST has two speed sensors.
Q11. Which of the followings is a part of the EST? 
EMC (Electro Magnetic Clutch)
G-sensor
Steering angle sensor
Front speed sensor
Q12. The trouble code will be erased automatically, if the transmission has reached a temperature of 50 °C or more for ( ) times or more without reoccurrence of the trouble
50
100
200
500
Q13. This A/T in the following picture is ?
4 speed HIVEC A/T
5 speed HIVEC A/T
6 speed HIVEC A/T
cannot identify
Q14. TPS signal is used in A/T to
Cool down the ATF temperature.
Determine the engine load.
Calculate the engine speed.
Determine the vehicle speed.
Q15. The difference between these two is that ( A ) connects two rotating parts and the ( B ) connects a part to the transmission housing, thereby holding it stationery
A: Clutch, B: Brake
A: Multiple disc type brake, B: Band type brake
A: Brake, B: Clutch
A: Accumulator, B: One-way clutch
Q16. Following picture is for 'photo interrupt type' steering angle sensor. Choose the correct statement. 
It is for TCS control only.
Normally it's signal transmits via CAN.
Calibration is required after replacement.
Steering wheel must be removed to replace this sensor.
Q17. When the stop lamp switch is failed in ESP system, ( ) fault can be caused by a faulty Brake Switch Signal circuit. 
Lateral G-sensor
Yaw-rate sensor
wheel speed sensor
pressure sensor
Q18. Under the condition in following picture, technician A says ABS/EBD also will be prohibited. Technician B says ABS/EBD functions are fully maintained. Who is right ? 
Technician A
Technician B
Both A and B
Neither A nor B
Q19. Following picture is for the exploded view of Bosch ESP HCU. Choose the correct statement. 
The pressure sensor cannot be replaced.
The pressure sensor is incorporated for ABS control only.
The pressure sensor is incorporated for EBD control only.
The pressure sensor must be inspected after replacement.
Q20. Choose the correct answer in the blank. 
A: Understeering, B: Oversteering
A: Oversteering, B: Understeering
A: Cornering force, B: Centrifugal force
A: Friction, B: Slip
Q21. After doing the following measurement, 
The clearance can be adjusted by new bearing
The clearance can be adjusted by new gear
The clearance can be adjusted by new shaft
The clearance can be adjusted by new snap ring
Q22. A heater gun is being used in following picture. Choose the proper statement.
Whenever overhaul the gear and shaft it is recommended to apply heat.
This process is applied only in case of press fitted gear.
For removal the gear from shaft, the shaft should be heated more than gear.
For assembly of gear, the shaft should be heated more than gear.
Q23. What is measured in following picture? 
Diameter and height of rail
Dimension of rail
Clearance of rail
Wear and deformation of rail
Q24. Choose the purpose of indicated part in following picture. 
To prevent gears from jumping out.
To give a solid shift feeling.
Both 1 and 2
None of the above
Q25. Choose the best description for the below picture. 
Free play between snap ring and bearing
Free play between bearing and housing
Zero play between snap ring and bearing
Press fitted condition for snap ring and bearing
Q26. Choose the best description for the below picture. 
Free play between snap ring and bearing
Free play between bearing and housing
Zero play between snap ring and bearing
Press fitted condition for snap ring and bearing
Q27. "The function of the ( ) mechanism is to equalize the speed of the hub and the gear to be shifted". Choose the best answer in the above blank.
Key spring
Poppet ball
Clutch
Synchronizer
Q28. The switches name on the following figure are 
Neutral switch, shift lock switch
Back-up lamp switch, shift lock switch
Back-up lamp switch, Neutral switch
1st gear detection switch, Neutral switch
Q29. One side has 3 oil grooves but other side has four in gear as shown in the below figure. When assemble the gear in manual transmission, 
The direction may be neglected.
The direction must be identified.
Must use the press always.
None of the above
Q30. Choose the correct assembly direction of slit on spring pin. 
A
B
Both A and B
Neither A nor B
Q31. Following picture is a ( ) electrical power steering system. 
Column assist type
Pinion assist type
Rack assist type
None of above
Q32. According to the following figure, we can recognize that 
The steering angle sensor should be calibrated again.
The steering angle sensor is brand new one.
The MDPS control module should be replaced.
The steering sensor well calibrated.
Q33. Which of the following is correct job after replacement of MDPS control module?
ASP calibration (in certain model)
Variant coding
Both 1 & 2
None of the above
Q34. The purpose of 'Variant coding' in MDPS system is 
To get optimum motor current.
To get optimum sensitivity of torque sensor.
To calibrate the torque sensor.
To calibrate the steering angle sensor.
Q35. The ( ) amount of ( ) axle will vary depends on the cornering condition in AGCS system.
Toe, front
Toe, rear
Camber, front
Camber, rear
Q36. Choose the correct input signal for Active Geometry Controlled Suspension system. 
TPS
Position sensor
APS
Variable force solenoid valve
Q37. While teaching the TCM for smooth shift feeling in HIVEC system without ETS, it is recommended to do it with TPS ratio of (_________)
10-20 %
30-40 %
Different values, repeated 5 times each
70-80 %
Q38. The DTC for input shaft speed or output shaft speed sensor in HIVEC system to be detected, the shift range must be positioned at (______).
D range only
Sports mode range only
Reverse range only
D or 3 ranges
Q39. If ATF temperature sensor becomes open circuit in HIVEC system, the fixed temperature value will be ( ) degrees of celcius.
60
80
120
150
Q40. What is the meaning of 'mode A' in HIVEC A/T on the below screen of Hi-scan Pro? 
A/T is controlled by vehicle speed, TPS ratio (sporty degree, braking, slope) on the not slant road.
A/T is controlled with 4th gear holding for engine braking while down shift on the down hill road.
A/T is controlled with 3rd gear holding for engine braking while down shift on the down hill road.
System has a fault and DTC was detected by TCM.
